HP ProCurve Networking

» Contact opnemen

ProCurve Networking by HP - Toepassingsnotities



Contents
» 1. Introduction
» 2. Prerequisites
» 3. Network diagram
» 4. Preconfiguring the wireless module
» 5. Policy configuration and adoption in wired and wireless networks
» 5.1. Create the marketing and finance WLANs
» 5.2. Set up authentication on the RADIUS server
» 5.3. Configure the 5400zl switch with the new VLANs

Downloads
» How to extend your wired network to wirelesss (PDF)

1. Introduction

This document describes how to extend your wired network to wireless.

Scenario: Your company has an established ProCurve wired infrastructure, centrally managed by ProCurve Manager (PCM), and now wants to implement wireless services.

Solution: Insert a Wireless Edge Services Module (WESM) in a ProCurve Switch 5400zl Series and deploy radio ports.

» Return to top

2. Prerequisites

The ProCurve Switch 5400zl Series in which you want to integrate the new module is already managed by ProCurve Manager Plus (PCM+).

» Return to top

3. Network diagram
Figure 1 shows the system configuration. This example uses a ProCurve Switch 5406zl.

To view the power consumption of the phone, issue the following command on the switchFigure 1. System configuration

» Return to top

4. Preconfiguring the wireless module
Before beginning, ensure that the ProCurve Switch 5406zl in which you want to integrate the new module is already managed by PCM+: To view the power consumption of the phone, issue the following command on the switch
  1. The WESM is inserted in slot F on the 5406zl switch. Perform basic configuration from the CLI interface of the switch:
To view the power consumption of the phone, issue the following command on the switch
When you insert a WESM into a switch slot, the switch automatically creates two virtual ports corresponding to the uplink and downlink ports of the WESM. For example, if you have inserted the module into slot F, it creates FUP (Virtual Uplink) and FDP (Virtual Downlink) virtual ports. FUP must be placed in the management VLAN (vlan 10).
To view the power consumption of the phone, issue the following command on the switch
  1. The WESM can be configured from its Web interface: http://10.1.10.5.
    Note: You need to have Java™ installed on your virtual server. If the software is not already installed, download and install it now.
    Log on as manager/procurve.
  2. On the first page you will see a warning:
    Country Code is not set. Use Network Setup page to set the country code.
    Go to the Network Setup page. Choose your country’s code and click Apply.To view the power consumption of the phone, issue the following command on the switch
  3. For radio port deployment and adoption, plug two radio ports into any of the ports configured with your wireless VLAN on the ProCurve Switch 5406zl. The orange LEDs will blink rapidly; after 30 seconds, the two LEDs will blink less rapidly, indicating that the radio ports have been adopted.
  4. To view radio port adoption on the WESM interface, go to Device Information | Radio Adoption Statistics. The two radio ports will appear:
To view the power consumption of the phone, issue the following command on the switch
  1. On the ProCurve Switch 5406zl, confirm that VLAN 2100 has been created. Also confirm that the radio ports detected by default by Layer Link Discovery Protocol (LLDP) are placed in this VLAN. The virtual downlink port has been automatically tagged in this VLAN:
To view the power consumption of the phone, issue the following command on the switch
  1. In PCM+, the ProCurve Wireless Edge Services zl Module appears with its two radio ports. Note that radio parameters (Channel, Tx Power, and RF Detection) can be easily viewed.
To view the power consumption of the phone, issue the following command on the switch
  1. If desired, you can modify radio port parameters from here. For example, to enable neighbor detection on one of the radios, select the second icon from the left, above the radio list, and choose Enable automatic channel selection.
    To view the power consumption of the phone, issue the following command on the switch

» Return to top

5. Policy configuration and adoption in wired and wireless networks

Now create two WLANs to enable wireless access for the Marketing and Finance groups.

5.1. Create the marketing and finance WLANs

  1. To begin creating the Marketing WLAN on the WESM, go to Network Setup | WLAN Setup and edit SSID 1:
To view the power consumption of the phone, issue the following command on the switch

Configure the following parameters for SSID 1:
SSID: Marketing
Description: WLAN for Marketing employees
VLAN ID: Dynamic Assignment
Authentication: 802.1X EAP
Encryption: WPA/WPA2-TKIP and WPA2-AES

To view the power consumption of the phone, issue the following command on the switch

  1. Open the Config menu (near the Encryption parameters) and enable Fast Roaming options for the WLAN:
    • PMK caching
    • Opportunistic Key Caching
    • Pre-Authentication
    When a wireless station has to roam, this enables it to associate more quickly with a new WESM.
    To view the power consumption of the phone, issue the following command on the switch
  2. To edit the RADIUS configuration, enter the address of the RADIUS server (10.1.10.10) and the RADIUS Shared Secret (procurve). Enable Re-authentication and choose CHAP as the Authentication Protocol.
    To view the power consumption of the phone, issue the following command on the switch
  3. Enable the SSID:
To view the power consumption of the phone, issue the following command on the switch
  1. Now use a similar procedure to create and enable a Finance WLAN on the WESM.
» Return to top

5.2. Set up authentication on the RADIUS server

  1. On the IAS RADIUS server, add the WESM as a new client, with shared secret procurve:
    To view the power consumption of the phone, issue the following command on the switch
  2. To configure IDM, from the Identity Management Configuration, create the new location wireless. From the Wireless Devices tab, select the Wireless Edge Services zl Module and include all radios:
    To view the power consumption of the phone, issue the following command on the switch

    To view the power consumption of the phone, issue the following command on the switch

    To view the power consumption of the phone, issue the following command on the switch
  3. Add a new rule to the Marketing Access Policy Group:
    Location: wireless
    Time: ANY
    System: ANY
    WLAN: Marketing
    Access Profile: Marketing
    To view the power consumption of the phone, issue the following command on the switch

    To view the power consumption of the phone, issue the following command on the switch
  4. Also add a new rule to the Finance Access Policy Group:
    Location: wireless
    Time: ANY
    System: ANY
    WLAN: Financev Access Profile: Finance
    Note: If you cannot see Marketing and Finance in the list of service set identifiers (SSIDs), re-discover the Wireless Edge Services zl Module from PCM.
» Return to top

5.3. Configure the 5400zl switch with the new VLANs

  1. To configure the 5400zl switch, tag the Marketing and Finance VLANs on port FUP.
To view the power consumption of the phone, issue the following command on the switch

This concludes the procedure for extending your wired network to wireless. If you have questions, additional information can be found in these sources:

» Return to top